Hiring Tips

Spots on Your Windows After a Clean and What Causes Them

Why windows can show spots after a clean, what is normal after a first pole clean, when it points to a problem with the water or technique, and how to ask for it to be put right.

Illustration of a window with a few water droplets beside a hose reel and a pole

Spots on your windows after a clean can have several causes, including old residue on a first pole clean, hard water from a garden hose, or worn filtration in the cleaning equipment. While it can be frustrating to see marks after paying for a service, some spotting can happen, especially on a first pole clean. A good window cleaner will want to know if the glass has dried with marks so they can correct the problem.

Spots after a clean and whether they are normal

Most domestic window cleaning is done on a regular round. The same cleaner returns on a set cycle, commonly every four, six or eight weeks. Work is priced per visit according to the size of the property, the number and type of windows, access and frequency. A first clean or a one-off clean usually costs more than a regular visit. London and the South East cost more.

Traditional cleaning uses an applicator, squeegee and cloth. However, many cleaners now work from the ground using a telescopic pole. The Health and Safety Executive says ladders can be a sensible option for low risk, short duration work on lower floors. The Work at Height Regulations 2005 require work at height to be properly planned, done by competent people and avoided where reasonably practicable.

Because of this, pole cleaning is very common. Industry guidance describes a water-fed pole as a telescopic pole with a brush and a means of delivering purified water. The use of purified water is an integral part of the cleaning process.

Because the minerals have been filtered out, the pure water is meant to dry without leaving any marks on the glass. The windows are scrubbed, rinsed and left wet to dry naturally. Some spotting can happen on a first pole clean. If it carries on, tell your cleaner.

The usual causes in plain terms

When pure water dries, it evaporates completely and leaves nothing behind. Spots appear when the water picks up dirt or minerals before it dries on the glass.

There are four main reasons why this happens:

  • Old residue from earlier cleans being rinsed out on a first pole clean.
  • Water filters in the cleaner's van reaching the end of their life and letting minerals through.
  • The wrong rinsing technique leaving dirty water on the lower panes.
  • Hard water from a garden hose or sprinkler spraying onto the window between cleans.

None of these automatically mean the cleaner is at fault, and a good cleaner will want to know about them. Extras like inside glass, conservatory roofs, roof windows, glazed doors, fascias and gutters are priced on top, and nothing is agreed about these areas unless you ask for them.

Old residue and a first pole clean

If your windows were previously cleaned another way, some old residue may be left on the glass and frames. A pure water system uses a brush to scrub the frames and the glass.

A first pole clean can leave some spotting until old residue has been rinsed out. This is why a water-fed pole clean can sometimes look worse before it gets better.

There is no reliable figure for how many cleans it takes for spotting to stop, so no number is given here. It is best not to judge a pole clean on the first visit.

Why the purity of the water matters

For the glass to dry clear, the water must be completely pure. Window cleaners use specialist filtration systems in their vans or trolleys to remove the minerals found in normal tap water. Over time, the resin and pre-filters in these systems wear out and need replacing.

Testing the water from the system with a TDS meter, which reads in parts per million, is a sensible check.

The target reading is:

Meter reading

What it means for the windows

Under 10 parts per million

The target result.

Over 10 parts per million

Points to exhausted filtration, so the resin and pre-filters need replacing.

If a cleaner is working with exhausted resin and pre-filters, the water is no longer as pure as it should be, and marks can result.

Wind, splash and the wrong rinse

How the cleaner rinses the window is just as important as the purity of the water. Insufficient rinsing is a cause of spots. The person doing the job must follow a specific order to keep dirty water away from clean glass.

The correct method is to scrub the frames first, then the glass. The rinse must start with the frames and then move to the glass in small sections. Crucially, they must rinse from the top down so runoff does not dry on lower glass. If they rush and rinse the bottom first, dirty water from the top will drip down and leave spots.

The weather can also cause problems on the day. Wind can blow dirty water from the frames back onto the clean glass. Splash back from sills or overspray from neighbouring windows can also leave marks. For wind, it helps to work on another side of the building and return once the wind dies down.

Hard water from hoses and sprinklers

Sometimes the spots are not caused by the window cleaner at all. If you use a garden hose to wash your car near the house, or you have a lawn sprinkler that hits the windows, you are spraying tap water onto the glass.

According to the Drinking Water Inspectorate, water hardness is caused by dissolved calcium and magnesium. Depending on local geology, the hardness of the water supply varies across the country.

The inspectorate measures this hardness in bands:

Water hardness type

Mineral content band

Soft

Up to 100 milligrams per litre

Slightly hard

100 to 150 milligrams per litre

Moderately hard

150 to 200 milligrams per litre

Hard

200 to 300 milligrams per litre

Very hard

Above 300 milligrams per litre

A map shows typical hardness across England and Wales, but there is local variation, so ask your water company for an accurate reading for your address.

When this hard tap water dries on your windows, the calcium and magnesium are left behind as stubborn white spots. Pure water then has to deal with those deposits.

Spots that will not rinse off

Existing hard water deposits on glass may not come off with a standard pure water clean.

In one trade forum thread, a practitioner advised removing the stains first and then finishing with a pure water clean. Another accepted some spotting on windows that would sit vacant for a month. This is one person's opinion rather than tested guidance.

If you have heavily stained windows from hard water or building work, you might need to remove hard water stains from glass yourself or ask your cleaner to quote for a restorative first clean. A quote is a fixed price for this extra work, whereas an estimate is not.

What to ask your cleaner

When you notice spots, the best approach is to ask your cleaner a few simple questions. This helps you understand what went wrong and gives them a chance to explain their process.

Ask these questions to get a clear picture:

  • Did you notice any heavy soap residue in the seals when you scrubbed the frames?
  • Is it possible the wind blew dirty water back onto the glass after you rinsed?
  • Have you tested the pure water recently to check the filter is still working?
  • Do you think there are existing hard water stains on the glass that need a stronger treatment?
  • Can I see a current certificate for your public liability insurance in case of damage?

A professional will be happy to answer these. Public liability insurance is not a legal requirement, but it is the cover that pays if a cleaner damages property or injures someone.

When dealing with window cleaners, always be wary of cold callers who claim to be the usual cleaner and ask for payment. You should also watch out for cleans carried out without agreement, followed by a bill. Industry guidance produced with the Health and Safety Executive says water-fed poles must not be used near overhead power lines. This is a very good reason to point out any overhead cable to the cleaner before they start work.

How to raise it politely and what you can expect

Under the Consumer Rights Act 2015, a service must be carried out with reasonable care and skill. If the spots turn out to come from poor rinsing or spent filters, the work may not have met this standard, but do not assume that before the cleaner has looked.

According to Citizens Advice, if a paid service has not been done with reasonable care and skill, you can ask for it to be redone or for a discount. The law says you must first give the trader the option of providing the service again if possible. You lose this right if you told them the service was good enough when it was done.

Wait for the glass to dry fully before you judge the finish. Note exactly when you saw the spots and take a few clear photographs. Send these to your cleaner, explain that you are unhappy with the finish, and ask them to look again. The law says the trader should first be given the chance to put it right.

If you agreed a service on the doorstep, by phone or online, it normally carries a 14-day cooling-off period. Avoid paying months in advance for a regular service.

Common questions

Do spots mean the cleaner used dirty water?

Not necessarily. Spots can come from worn filtration, from old residue being rinsed out on a first pole clean, from poor rinsing, or from wind and splash back. Ask your cleaner to look at the glass before deciding the cause.

Will the spots stop happening on the next clean?

A first pole clean can leave some spotting until old residue has been rinsed out, but there is no reliable figure for how many cleans that takes. If the problem is exhausted filtration, the resin and pre-filters need replacing. Tell your cleaner if the spots continue.

Can rain cause spots on freshly cleaned windows?

It can. Splash back from sills or frames can leave marks, so note when you first saw the spots and whether it had rained. Mention that to your cleaner.

Should I wipe the spots off with a cloth?

It is best to leave the spots and contact your cleaner. Let the cleaner see them as they are and return to rinse the window again.

What to do next

Dealing with spots after a window clean is mostly about communication. Follow these simple steps to get the problem sorted:

  • Wait for the windows to dry completely before checking for marks.
  • Check if the spots are on every window or just a few specific panes.
  • Take clear photographs of the spotting on the glass.
  • Contact your cleaner politely and ask them to return and check the finish.
  • Point out any garden sprinklers or hoses that might be spraying hard water onto the house.
  • Ask to see their public liability insurance certificate just in case.

A few spots on a first visit are nothing to worry about, but a professional will always want to put things right. If you decide it is time to look for a new service, you can use our directory to find a window cleaner near you.

Find a top rated window cleaner near you

1,649 window cleaners across the UK, each ranked on their Google rating and the number of reviews behind it. Start with your county:

All counties and towns · The UK Top 100 window cleaners

Amy Fisher
Written by
Amy Fisher Writer

Amy researches and writes guides for Top Rated Window Cleaners, turning prices, rules and official guidance into plain advice for homeowners. She is a keen birdwatcher.

Looking for a trusted window cleaner? Browse our verified listings.

Find a Window Cleaner